idt90e36三相电能表设计方案

发布时间:1/12/2015 | 681 次阅读
idt公司的idt90e32/36三相电能计量芯片,集成了7个单独的2阶sigma-delta adc,可实现三相四线系统中的三个电压通路(a,b和c相)和四个电流通路(a,b,c相和中线),和标准iec62052-11, iec62053-22 and iec62053-23, ansi c12.1与ansi c12.20兼容,动态范围6000:1时的有功功率精度±0.1%,无功功率精度±0.2%,片内的基准电压温度系数6 ppm/ ℃,主要用于0.5s 级或1级三相四线(y0)和三相三线(y或δ)电表,数据采集终端,电源监视仪表等.本文介绍了90e36主要特性,方框图以及三相四线电流互感器(ct)电表电路图和材料清单, 三相四线rogowski线圈电表电路图和材料清单, 三相三线电表电路图和材料清单.

the 90e36 is a poly-phase high performance wide-dynamic range metering ic. the 90e36 incorporates 7 independent 2nd order sigma-delta adcs, which could be employed in three voltage channels (phase a, b and c) and four current channels (phase a, b, c and neutral line) in a typical three-phase four-wire system.

the 90e36 has an embedded dsp which executes calculation of active energy, reactive energy, apparent energy, fundamental and harmonic active energy over adc signal and on-chip reference voltage.

the dsp also calculates measurement parameters such as voltage and current rms value as well as mean active/reactive/apparent power.

a four-wire spi interface is provided between the 90e36 and the external microcontroller. in addition, dma mode can be used for 7-channel adc raw data access, offering more flexibility in system application.

the 90e36 is suitable for poly-phase multi-function meters which could measure active/reactive/apparent energy and fundamental/harmonic energy either through four independent energy pulse outputs cf1/cf2/cf3/cf4 or through the corresponding registers.

with the on-chip thd and dft engine, all phases’ thd and dft results can be directly accessed through related registers, thus simplifying hardware design in data acquisition terminals.

idt’s proprietary adc and auto-temperature compensation technology for reference voltage ensure the 90e36’s long-term stability over variations in grid and ambient environment conditions.

90e36主要特性:

metering features

? metering features fully in compliance with the requirements of iec62052-11, iec62053-22 and iec62053-23, ansi c12.1 and ansi c12.20; applicable in class 0.5s or class 1 poly-phase watt-hour meter or class 2 poly-phase var-hour meter.

? accuracy of ±0.1% for active energy and ±0.2% for reactive energy over the dynamic range of 6000:1.

? temperature coefficient is 6 ppm/ ℃ (typical) for on-chip reference voltage.

? single-point calibration on each phase over the whole dynamic ange for active energy; no calibration needed for reactive/ apparent energy.

? ±1 ℃ (typical) temperature sensor accuracy.

? electrical parameters measurement: less than ±0.5% fiducial error for vrms, irms, mean active/ reactive/ apparent power, frequency, power factor and phase angle.

? active (forward/reverse), reactive (forward/reverse), apparent energy with independent energy registers. active/ reactive/ apparent energy can be output by pulse or read through energy registers to adapt to different applications.

? programmable startup and no-load power threshold, special designed of startup and no-load circuits to eliminate crosstalk among phases achieving better accuracy especially at low power conditions.

? dedicated adc and different gains for phase a/b/c and neutral line current sampling circuits. current sampled over current transformer (ct) or rogowski coil (di/dt coil); phase a/b/c voltage sampled over resistor divider network or potential transformer (pt).

? programmable power modes: normal mode (n mode), idle mode (i mode), detection mode (d mode) and partial measurement mode (m mode).

? fundamental (cf3, 0.2%) and harmonic (cf4, 1%) active energy with dedicated energy and power registers.

? total harmonic distortion (thd) and discrete fourier transform (dft) functions for 2 ~ 32 order harmonic component. thd and dft results available in spi accessible registers. both voltage and current of all phases processed within the same time period.

? event detection: sag, phase loss, reverse voltage/ current phase sequence, reverse flow, calculated neutral line current inc overcurrent sampled neutral line current ins overcurrent and thd+n over-threshold.

other features

? 3.3v single power supply. operating voltage range: 2.8v~3.6v. metering accuracy guaranteed within 3.0v~3.6v.

? four-wire spi interface with direct memory access (dma) mode to stream out 7-channel adc raw data.

? parameter diagnosis function and programmable interrupt output of the irq interrupt signals and the warnout signal.

? programmable voltage sag detection and zero-crossing output.

? cf1/cf2/cf3/cf4 output active/ reactive/ apparent energy pulses and fundamental/ harmonic energy pulses respectively.

? crystal oscillator frequency: 16.384 mhz. on-chip two capacitors and no need of external capacitors.

? tqfp48 package.

? operating temperature: -40 ℃ ~ +85 ℃ .

90e36应用:

? poly-phase energy meters of class 0.5s and class 1 which are used in three-phase four-wire (3p4w, y0) or three-phase threewire (3p3w, y or δ) systems.

? data acquisition terminal.

? power monitoring instruments which need to measure voltage, current, thd, dft, mean power, etc.

深圳市鹏拓发展电子
  • 联系人:马先生 林先生 马小姐

    975586346

  • 电话:0755-82773839
  • 邮箱: prydz168@qq.com
  • 地址:深圳市福田区华强北华联发大厦六楼635房
深圳市瑞斯特电子科技有限公司
  • 联系人:杨锐锋

    515035790

  • 电话:0755-82550910/13189682405
  • 邮箱:szruist@126.com
  • 地址:深圳福田区华强广场二楼Q2B046
北京元坤伟业科技有限公司
  • 联系人:刘先生

    1584878981/378319812

  • 电话:010-62104931/62104891/62104578/62106431/62104791
  • 邮箱:sale1@yuankun24.com
  • 地址:北京市海淀区中关村大街32号和盛嘉业大厦10层1008室