此规格适用于“汽车排插连接器”系列
this spec is applicable for “car line connector”series.
二、额定值:dc 34v 2a
norminal rating: dc 34v 2a
三、构造(struction)
3.1形状,尺寸根据图纸确定( form, dimension according to the drawing).
3.2各部分无生锈、裂痕、电镀不良现象(without rust and oxydation、crack、defective electric plating in all parts)
3.3适应基板厚度(applicble pc board thickness):1.6mm
四、温度范围(temperature range):-25°c~85°c;
五、材质( material)
5.1塑胶:pbt plastic (part: pbt)
5.2端子:磷青铜、铍铜(terminal:be-bronze、phosphor-bronze);
六、电气性能(electrical characteristics)
no | 测试项目 test item | 试验方法及条件 (test condition & method) | 规格standard |
6.1 | 接触阻抗contact impedance | 公座和母座导体之间的接触电阻(measured the resistance of mated pin header ) | 30毫欧以下 (below 30mω) |
6.2 | 绝缘阻抗insulation impedance | 在端子之间和端子与壳之间加dc500v条件下持续1分钟测量among terminals or between terminal and shell, under condition of dc500v ,last 1min to test | 1000兆欧以上 ( above100mω) |
6.3 | 耐电压disruptive test | 在端子之间和端子与壳之间加ac 500v(50h或60h)条件下持续1分钟测量among terminals or between terminals and shell, under condition of ac 500v(50h or 60h),last 1min to test | 无击穿现象出现 ( without disruptive ) |
七、机械性能( mechancial character)
no | 测试项目 test item | 试验方法及条件 (test condition & method) | 规格standard |
7.1 | 插入力与拔出力度insert and pull out | 用配套插头插入插座再从中拔出;测量插入和拔出的作用力make the the force of insert the socket and pullout | 插入力度:0.7kgfmax insert force: 0.7kgf max 拔出力度:0.3kgf-2.6kgf pullout force : 0.3kgf to 2.6 kgf |
7.2 | 端子强度 terminal strength | 顺端子弹力方向施加500g力条件下持续10秒 add 0.5kgf along the terminal spring , last 10 seconds | 未有裂纹与失去弹性 wiouth fault trace, still with elastic sensation |
八、环境试验(environmental performance)
no | 测试项目 test item | 试验方法及条件 (test condition & method) | 规格standard |
8.1 | 耐高温试验 hight temperature resistance test | 在环境中放96小时,再放在正常环境中30分钟后进行测试test after lasting 96hours under 90±2°c,and then staying 30mins under normal environment | - 无任何迹象显示机械及电气性能损坏(mechanical characteristic &electrical characteristic are well )
|
8.2 | 耐低温试验 low temperature resistance test | 在-20±3°c环境中放96小时,再放在正常环境中30分钟后进行测试test after lasting 96hours under -20±3°c,and then staying 30mins under normal environment |
8.3 | 盐雾试验salt spray test | 把试验样品从试验箱悬挂起来,采用浓度为(5±0.1)%(质量百分比)的氯化纳溶液连续雾化16小时,试验后用流动的蒸溜水轻轻洗去表面沉积物,在常温条件下恢复1-2小时hang up the sample for 16hours in the test box of (5±0.1)%(mass percent) nacl solution, after that flush away the surfacial deposit lightly with running distilled water; finally, under normal environment, make it lay 1-2 hours | 外观无损伤 (五金件应无露出底金属的严重锈蚀,使用预定好的型材,其落料而允许有不影响其性能的轻微腐蚀) the sample apperance surface is well, non-corroded.(the inside metal of the metal part isn’t badly corroded, slight corrode is possible ,but it doesn’t influence the character. |
九、其它试验(other characteristic)
no | 测试项目 test item | 试验方法及条件 (test condition & method) | 规格standard |
9.1 | 可焊性试验 weldability test | 将端子顶部浸入焊锡池2mm深;温度270±5°c;时间2±0.5秒 infusion the terminal top into soldering acid 2m deep; termperature: 270±5°c ;duraton: 2±0.5 seconds | 浸入部分90%以上表面被锡覆盖 90% of the part infused is plating by tin |
9.2 | 寿命试验life testing | 在无负荷条件下以每分钟15-18次的速度操作10000次 under unloaded condition ,working ten thousand times at the speed of 15-18 times per min | - 接触阻抗150毫欧,变化范围初始值(30%)contact resistance < 150mω>,variation range initial value(30%)
|
一、此规格适用于“汽车排插”系列
this spec is applicable for “car line connector”series.
二、额定值:dc 34v 2a
norminal rating: dc 34v 2a
三、构造(struction)
3.1形状,尺寸根据图纸确定( form, dimension according to the drawing).
3.2各部分无生锈、裂痕、电镀不良现象(without rust and oxydation、crack、defective electric plating in all parts)
3.3适应基板厚度(applicble pc board thickness):1.6mm
四、温度范围(temperature range):-25°c~85°c;
五、材质( material)
5.1塑胶:pbt plastic (part: pbt)
5.2端子:磷青铜、铍铜(terminal:be-bronze、phosphor-bronze);
六、电气性能(electrical characteristics)
no | 测试项目 test item | 试验方法及条件 (test condition & method) | 规格standard |
6.1 | 接触阻抗contact impedance | 公座和母座导体之间的接触电阻(measured the resistance of mated pin header ) | 30毫欧以下 (below 30mω) |
6.2 | 绝缘阻抗insulation impedance | 在端子之间和端子与壳之间加dc500v条件下持续1分钟测量among terminals or between terminal and shell, under condition of dc500v ,last 1min to test | 1000兆欧以上 ( above100mω) |
6.3 | 耐电压disruptive test | 在端子之间和端子与壳之间加ac 500v(50h或60h)条件下持续1分钟测量among terminals or between terminals and shell, under condition of ac 500v(50h or 60h),last 1min to test | 无击穿现象出现 ( without disruptive ) |
七、机械性能( mechancial character)
no | 测试项目 test item | 试验方法及条件 (test condition & method) | 规格standard |
7.1 | 插入力与拔出力度insert and pull out | 用配套插头插入插座再从中拔出;测量插入和拔出的作用力make the the force of insert the socket and pullout | 插入力度:0.7kgfmax insert force: 0.7kgf max 拔出力度:0.3kgf-2.6kgf pullout force : 0.3kgf to 2.6 kgf |
7.2 | 端子强度 terminal strength | 顺端子弹力方向施加500g力条件下持续10秒 add 0.5kgf along the terminal spring , last 10 seconds | 未有裂纹与失去弹性 wiouth fault trace, still with elastic sensation |
八、环境试验(environmental performance)
no | 测试项目 test item | 试验方法及条件 (test condition & method) | 规格standard |
8.1 | 耐高温试验 hight temperature resistance test | 在环境中放96小时,再放在正常环境中30分钟后进行测试test after lasting 96hours under 90±2°c,and then staying 30mins under normal environment | - 无任何迹象显示机械及电气性能损坏(mechanical characteristic &electrical characteristic are well )
|
8.2 | 耐低温试验 low temperature resistance test | 在-20±3°c环境中放96小时,再放在正常环境中30分钟后进行测试test after lasting 96hours under -20±3°c,and then staying 30mins under normal environment |
8.3 | 盐雾试验salt spray test | 把试验样品从试验箱悬挂起来,采用浓度为(5±0.1)%(质量百分比)的氯化纳溶液连续雾化16小时,试验后用流动的蒸溜水轻轻洗去表面沉积物,在常温条件下恢复1-2小时hang up the sample for 16hours in the test box of (5±0.1)%(mass percent) nacl solution, after that flush away the surfacial deposit lightly with running distilled water; finally, under normal environment, make it lay 1-2 hours | 外观无损伤 (五金件应无露出底金属的严重锈蚀,使用预定好的型材,其落料而允许有不影响其性能的轻微腐蚀) the sample apperance surface is well, non-corroded.(the inside metal of the metal part isn’t badly corroded, slight corrode is possible ,but it doesn’t influence the character. |
九、其它试验(other characteristic)
no | 测试项目 test item | 试验方法及条件 (test condition & method) | 规格standard |
9.1 | 可焊性试验 weldability test | 将端子顶部浸入焊锡池2mm深;温度270±5°c;时间2±0.5秒 infusion the terminal top into soldering acid 2m deep; termperature: 270±5°c ;duraton: 2±0.5 seconds | 浸入部分90%以上表面被锡覆盖 90% of the part infused is plating by tin |
9.2 | 寿命试验life testing | 在无负荷条件下以每分钟15-18次的速度操作10000次 under unloaded condition ,working ten thousand times at the speed of 15-18 times per min | - 接触阻抗150毫欧,变化范围初始值(30%)contact resistance < 150mω>,variation range initial value(30%)
|