specification for approval customer name:
part no. :
issue date ： 2010-11-10
深 圳 市 谷 科 半 导 体 有 限 公 司 |
quality dept. | engineering dept. | producer |
| | |
■mechanical dimensions note: 1. all dimensions are in millimeters. 2. all dimensions without tolerances are for reference only. 3.material as follows: package: heat-resistant polymer electrodes: cu plating copper alloy |
■absolute maximum ratings (ta = 25℃): items | symbol | absolute maximum rating | unit | blue/green/white | red/yellow | power dissipation * | pd | 6 | 6 | w | dc forward current | if | 300 | 300 | ma | peak pulse forward current* | ifp | 600 | 600 | ma | average forward current | iavg | 300 | 300 | ma | reverse voltage | vr | 7 | 7 | v | led junction temperature | tj | 120 | 120 | ℃ | operating temperature | top | -30 ~ +60 | -30~+60 | ℃ | storage temperature | tstg | -40 ~ +100 | -40 ~ +100 | ℃ | soldering temperature | tsol | max.240°c for 5 sec max (4mmfrom the base of the lens ) |
*pulse width≦0.1msec duty≦1/10 ■typical electrical & optical characteristics ( ta = 25℃): part no | color temperature | forward voltage(v) | test condition | viewing angle (typ.) | luminous flux （lm） | min. | typ. | max. | p6wx015a24wc-02 | 6000-6500k | 19 | 20 | 21 | if= 300ma | 140 | 500-600 | | | | | | | | | | | | | | | | | |
■notes: 1.absolute maximum ratings ta=25℃. 2.tolerance of measurement of forward voltage±0.1v. 3.tolerance of measurement of luminous flux ±15%. |
■ room temperture operating life reliability test result 常温点亮信耐性结果 （ta=25℃,if=300ma）use ssc ciruit board￡heat sink(tj=50℃) life time graph |
light output characteristics wavelength characteristics relative intensity vs wavelength (nm) |
typical representative spatial radiation pattern of single led |
■reliability
1.test items and results
classi- fication | test item | reference standard | test conditions | duration | units tested | number of damaged |
operation test | operating life test | | ta=25℃±5℃，if=350ma | 1000 hrs | 22 | 0/22 |
environment test | high temperature storage | jeita ed-4701 200 201 | ta=100℃±5℃ | 1000 hrs | 22 | 0/22 |
low temperature storage | jeita ed-4701 200 201 | ta=－40℃±5℃ | 1000 hrs | 22 | 0/22 |
temperature. & humidity storage | | ta=85℃±5℃， rh=85%±5%rh | 1000 hrs | 22 | 0/22 |
thermal shock | jeita ed-4701 300 307 | -40°±5℃çè+85℃±5℃ 30min dwell / 5 min transfer | 50 cycles | 22 | 0/22 |
soldering test | solder ability | | 240±5℃，5±1 sec | 1 time over 95%wetting | 22 | 0/22 |
resistance to soldering heat | | 260±5℃，10±1 sec | 1 time | 22 | 0/22 |
2.failure criteria
－ electrical failures:
－ vfshift% >10%
－ ir(vr=7v)>1ua
－ visual failures:
－ broken or damaged package or lead
－ solder ability < 95% wetting
－ dimension out of tolerance
－ discolor of lens
■note：it is required that the leds should be attached heat-sink when these leds are operating.
precautions for use
(一) storagre
in order to avoid absorption of moisture it is recommended thm the products are stored in the dry box (or dessicator) with a dessicant.alternatively the tollowing environment is
recommended:
storage temperature :5℃～30℃ humidity:60%hrmax
(二). any mechanical force or any ekcess vibration should be avoied daring the cooling
process after soldering.
(三). components should not be monnted on distorted printed ciruit boards.
(四). devices should not be used in any type of fluid such as water,oil,organic solvents etc.
when cleaning is required,ipa should be used .
(五). devices should be soldered with in 7 days after opening the moistare-proof packing.
(六). esd precaution .static electrcity and surge damages leds.
it is recommended that wrist bands or anti-electrostatic gloves be uses when handing the
leds.all devices,equipment and machinery should be properly grounded.
使 用 说 明
一．贮存：
为避免吸潮建议将产品贮存在放有干燥剂的干燥柜中，贮存温度为：5℃～30℃，湿度：≦60%hr
二．产品在焊锡后冷却过程中避免机械压力和过大震动。
三．禁止焊接在变形pcb板上。
四．产品不得接触水。油。有机溶液。
五．打开防潮包装后7天内产品使用完毕。
六．防静电要求：
使用产品时，必须戴防静电环或防静手套，所有设备。装置。机台必须有效接地